Baumatic PHC720SS Manual de usuario

PHC620SS 60 cm/ PHC720SS 77 cm Front touch control ceramic hob

Ceramic hob surface layout PHC620SS PHC720SS 10

Control panel layout PHC620SS PHC720SS 1. ON/OFF button 2. Safety lock button 3. Safety lock neon 4. Plus button 5. Minus button 6. Cooking

PHC720SS Using the ceramic hob Before first use IMPORTANT: You should clean the ceramic hob surface (see “Cleaning and maintenance” section). o

Turning the hob on o Press the ON/OFF button (1) o The cooking zone indicators (6) will all read “0”. o The decimal point symbols (7) wi

Turning off a zone instantly o Press the minus button (5) and the plus button (4) simultaneously. o The zone will switch off immediately. o A

o Use the plus (4) or minus (5) buttons of the dual circuit zone that you wish to use and select a power level between 1 and 9. o The central sec

Locking the hob top o The whole hob top can be locked by pressing the safety lock button (2) whilst the appliance is turned on. o The safety lock

Automatic pre-heating o This feature will set a cooking zone to maximum power and will then automatically set the cooking zone to a power level

Increasing the power level during automatic pre-heating o If a zone is already within automatic pre-heating mode and you wish to adjust the power l

19o After selecting the timer, a zone must be selected within 10 seconds by pressing one of the plus (4) or minus (5) buttons. You should use these

User Manual for your Baumatic PHC620SS 60 cm PHC720SS 77 cm Front touch control 4 hyperspeed zone ceramic hob. NOTE:

20o The positions where the heat will radiate from are clearly marked on the hob top. The saucepans must be positioned exactly on these zones for ef

Cleaning and maintenance Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains su

Using a ceramic hob scraper Your appliance will be provided with a hob scraper. The following guidelines should also be followed when using the ceram

Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is locat

o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it. o Carefu

o Place the fixing brackets (B) over each hole and clip, and then place a screw (C) through the hole and fixing bracket (B). Tighten the screws a lit

Connecting the mains supply cable o The mains terminal block is located on the underside of the hob and the terminals are accessible by removing the

Replacing the mains supply cable If the mains supply cable is damaged, then it must be replaced by an appropriate replacement. The mains supply cab

28o The residual heat indicator has not come on after I have switched a cooking zone off. * The cooking zone has only been turned on for a short p

IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Baumatic

3Contents Environmental note 4 Important safety information 5 – 8 Specifications 8 – 9 Ceramic hob surface layout 10 Contr

Czech Republic Baumatic CR spol s.r.o. Amperova 495 46215, Librec Czech Republic +420 800 185 263 United Kingdom www.baumatic.cz Baumatic Ltd

2

Environmental note 4 o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard

Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before atte

6Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch

Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disco

o Pans should be lifted on and off the hob surface and not dragged. o Cooking zones should not be switched on without cookware placed on it. Also t

PHC720SS Product dimensions Height: 510 mm Width: 770 mm Depth: 40 mm Aperture dimensions Height: 490 mm Width: 750 mm Product specifications